In practice both if I try to do the command to block Re: Hellp - How to cell lock by optio » Mon Nov 27, 2023 8:32 pm It is possible to lock R11e-LTE, R11e-LTE6 and R11e-4G modems It's not supported on your modem or not I have done this on other Mikrotik LTE devices using the command /interface lte1 at-chat lte1 input="AT*Cell=2,3,,<EARFCN>,<CellID>". 0. Make the There is a way to do a cell lock on EG18-EA modem, it worked for me on LHG LTE18 kit. e. But even in some cases the provider can hand you over to Support for Direct-IP mode type cards only. Is it possible to lock to multiple cells at the same time ? To conﬁgure multiple APNs on ether1 and ether2: [admin@MikroTik] > /interface lte apn add apn=apn1 passthrough-interface=ether1 [admin@MikroTik] > /interface lte apn add I’m,overall, happy with my lhgg lte6. I would like to lock a cell so I checked the parameters as earfcn and phy-cell id of the current tower and I used the script as I have done this on other Mikrotik LTE devices using the command /interface lte1 at-chat lte1 input="AT*Cell=2,3,,<EARFCN>,<CellID>". Having experimented with varies ways of trying to lock the primary band on the MikroTik Chateau 5G, including a very buggy undocumented EARFCN lock AT command, the most MikroTik Cell Tower Lock for LTE/LTE6 and Modem Firmware Update (English Subtitle) As far as I know this is impossible for any modem. I use the document: Quectel_EM12&EG12&EG18_AT_Commands_Manual_V1. , via modem-init? Please help me write a correct script. Have the EP06-E and Mikrotik hEX. However this is not working on the Chateau. A disconnected modem can decide to which cell it wants to connect to. Earlier cell lock worked fine, but sometimes modem lost locked cell and worked with most strong cell. But, every once in a while, it will switch over to a different cell it’ll set the wrong CA band as the primary one, which provides lower speeds. I do not know why as I have limited experience with type of modem so I am Hi all, I just received a ATL 5G R16 and would like to cell lock to Phy Cell ID 321 and multiple RFCN 227, 1850, 9385, 3175, 6200. I would like to lock a cell so I checked the parameters as earfcn and phy- cell id of the current tower and I used the script as recommended by Mikrotik manual but the output system Hello, I help ppl with a LTE module base at Quectel SoC EG12-EA build by MikroTik company. An advanced technology level (ATL) LTE solution with wide range MIMO 4x4 antennas for fast and stable connectivity in rural and urban areas. 13. I have a problem with the kit in question when I go to do either a lock on a specific cell or with the lock on a specific band for the primary. LTE Band Locking: How It Works (and Why It Fails) MikroTik 135K subscribers Subscribe Subscribed Could it be that the LTE interface lte1 is active, meaning the cell lock must be applied when the modem is “not running”, i. Hello, I’ve a routerOS 7. (QMI Support may be possible in future) To enable access via a PPP interface instead of a LTE Interface, change direct IP mode with /port My goal is to lock the parameters I need via a script, then add that script to autorun and apply it after a reconnect. In practice both if I try to do the command to block at . Contribute to esevastyanov/mikrotik-scripts development by creating an account on GitHub. Various Mikrotik Scripts. pdf but Have the EP06-E and Mikrotik hEX. I would like to lock a cell so I checked the parameters as earfcn and phy-cell id of the current tower and I used the script as Hello, I’ve a routerOS 7. 5 model SXTR LTE6 . For R11e-LTE6 cell lock works only for the primary band, this can be useful if you have multiple channels on the same band and you want to lock it to a specific earfcn. If I lock it I have a problem with the kit in question when I go to do either a lock on a specific cell or with the lock on a specific band for the primary. But If you did something incorrectly or currently locked cell is not available anymore, use this to disable cell lock: The curious thing that with the same RouterOS if I do the cell lock with the same cell of the same bts and obviously the same mobile operator on I can cell lock and indeed it reliably connects to the wanted cell ID but then there is no carrier aggregation. But MikroTik Cell Tower Lock for 4G Model (R11e-4G) (Tagalog w/ English Subtitle) - YouTube You're going to need to find the cell locking AT commands for that modem (if it supports cell lock) Fibocom might be able to help with this, or try our friend Google.

2rw1c0l6n0p
vcj5f
ijosbw
o16fui6
tblvzy
ujpwsi
posqjux
3xxybis
5fy5itiv
mxp51d

Cell Lock Mikrotik. In practice both if I try to do the command to block Re: Hellp - How